TYPE#1 6802/6303 USB Consult Hardware Installation Manual V3.2 Type 1 - Rev3A/3B / 4 Boards (JECS ECCS 1984-1989 Legacy Engine Control Unit
NIStune Type 1 Hardware Installation Page 10 of 10 To remove the two ROM chips (U3 and U4) desolder from the top side of the ECU. Be very carefu
NIStune Type 1 Hardware Installation Page 11 of 11 The below picture shows the removed ICs, installed 28 pin machine drilled socket and four wir
NIStune Type 1 Hardware Installation Page 12 of 12 B. 1986 Single Board - Dual ROM ECUs Vehicles: Z31 300ZX VG30 1986-1987, CR31 / VL / VLT RB3
NIStune Type 1 Hardware Installation Page 13 of 13 2. Where the 28 pin ROM has been removed, replace this with a 28 pin machine drilled socket.
NIStune Type 1 Hardware Installation Page 14 of 14 C. 1987 Single Board - Single ROM ECUs Vehicles: Z31 300ZX VG30 1987, VL RB30 These ECUs onl
NIStune Type 1 Hardware Installation Page 15 of 15 D. 1989 Single Board - Single ROM - Header Connector ECUs Vehicles: Z31 VG30 late, HR31 RB20,
NIStune Type 1 Hardware Installation Page 16 of 16 S13 CA18DE/DET A31 RB20DE/DET
NIStune Type 1 Hardware Installation Page 17 of 17 EK10 MA09ERT / S13 KA24E 1. Remove the factory ROM chip, install a 28 pin machine drilled s
NIStune Type 1 Hardware Installation Page 18 of 18 4. CPU Header Connector Installation (X1) The NIStune board will come supplied with two heade
NIStune Type 1 Hardware Installation Page 19 of 19 A. Early Model ECUs You need to solder the following wires to the HD6802 processor similar to
NIStune Type 1 Hardware Installation Page 2 of 2 IINNTTRROODDUUCCTTIIOONN Welcome to NIStune. The NIStune hardware and software solution provi
NIStune Type 1 Hardware Installation Page 20 of 20 B. Later Model ECUs Later model ECUs connect directly to the circuit board using through hol
NIStune Type 1 Hardware Installation Page 21 of 21 J30 Maxima Connector Wire 1 - ECU throughhole D Connector Wire 2 - ECU throughhole C Conne
NIStune Type 1 Hardware Installation Page 22 of 22 A31 RB20 Connector Wire 1 - ECU throughhole near 61 Connector Wire 2 - ECU throughhole ...
NIStune Type 1 Hardware Installation Page 23 of 23 5. USB Connector Installation (X2) The USB-B style connector that comes with the NIStune boa
NIStune Type 1 Hardware Installation Page 24 of 24 Then put the USB-B socket inside the bracket and refasten the bracket as seen below. If y
NIStune Type 1 Hardware Installation Page 25 of 25 6. Inserting The Board Push the NIStune board into the machine drilled socket previously ins
NIStune Type 1 Hardware Installation Page 26 of 26 HR31 HR20 Installation
NIStune Type 1 Hardware Installation Page 27 of 27 7. Securing The Board Is is the responsbility of the installer to ensure that an vibration th
NIStune Type 1 Hardware Installation Page 28 of 28 8. Installing In The Vehicle Put the ECU casing back together and reinstall ECU into the meta
NIStune Type 1 Hardware Installation Page 29 of 29 9. Upgrading ECU MAF hardware Early model engine control units such as Z31, R31, most HR31 (
NIStune Type 1 Hardware Installation Page 3 of 3 TERMS AND CONDITIONS Nistune Developments has performed necessary measures to ensure that the N
NIStune Type 1 Hardware Installation Page 30 of 30 6. Rewire the AFM as per pinouts in the AFM section of the Nistune Software Users Manual 19
NIStune Type 1 Hardware Installation Page 31 of 31 1986-1988 HR31 RB20DET Note the later year models (such as MEC-R70 do not require this modifi
NIStune Type 1 Hardware Installation Page 32 of 32 10. Reading the factory ROM image ECU Type A (1984-1985) These ECUs have two non-standard
NIStune Type 1 Hardware Installation Page 33 of 33 1. So ensure you select the correct chip type matching your ROM/EPROM chip. Then select the re
NIStune Type 1 Hardware Installation Page 34 of 34 RREEVVIISSIIOONN HHIISSTTOORRYY DATE VERSION DESCRIPTION 21/12/2005 1.0 Document Creati
NIStune Type 1 Hardware Installation Page 4 of 4 Nistune Developments may, from time to time, revise or update the Software. In so doing, Nistune
NIStune Type 1 Hardware Installation Page 5 of 5 WARNING If your ECU pulses the fuel pump, injectors, fuel regulator, flashes LEDs randomly (or
NIStune Type 1 Hardware Installation Page 6 of 6 TABLE OF CONTENTS 1. Removing the ECU...
NIStune Type 1 Hardware Installation Page 7 of 7 1. Removing the ECU Locate the ECU in vehicle to be modified. The location of the factory ECU c
NIStune Type 1 Hardware Installation Page 8 of 8 2. Opening the ECU For NIStune board installation, firstly remove the top and bottom lids fro
NIStune Type 1 Hardware Installation Page 9 of 9 3. Resocketing the ECU A. 1984-1985 Dual Board - Dual ROM ECUs Vehicles: Early Z31 300ZX and E
Kommentare zu diesen Handbüchern